AutoRouteFailures Properties

Name	Return Type	Description
P AttemptToConnectNonSlopingElementToSlopedPipeError	FailureDefinitionId	You have specified that sloped pipe be drawn, but are trying to connect to an element that doesn't support sloping connections.
P AttemptToConnectNonSlopingElementToSlopedPipeWarning	FailureDefinitionId	You have specified that sloped pipe be drawn, but are trying to connect to an element that doesn't support sloping connections.
P DesignOptionConflictError	FailureDefinitionId	The solution is failing to do the elements are not in the same Design Option.
P DesignOptionConflictWarning	FailureDefinitionId	The solution is failing to do the elements are not in the same Design Option.
P DistributionTypeInvalid	FailureDefinitionId	Selected distribution system type is invalid!
P ElementHasFlowCalculation	FailureDefinitionId	This element has an open connection. This may not be an error, but for flow calculations to work correctly all connections should be sealed with an end cap.
P ElementHasOpenConnection	FailureDefinitionId	This element has an open connection. This may not be an error, but all open connections should be sealed with an end cap.
P FailedDowngradeCrossToElbow	FailureDefinitionId	Failed to downgrade tee type to elbow type.
P FailedDowngradeCrossToTee	FailureDefinitionId	Failed to downgrade cross type to tee type.
P FailedDowngradeTeeToCross	FailureDefinitionId	Failed to upgrade tee type to cross type.
P FailToDoCompatiblePhaseError	FailureDefinitionId	The solution is failing to do the elements Phases are compatible.
P FailToDoCompatiblePhaseWarning	FailureDefinitionId	The solution is failing to do the elements Phases are compatible.
P FailToIntersectParallelSegmentsError	FailureDefinitionId	The solution is failing to do segments which are parallel and should intersect.
P FailToIntersectParallelSegmentsWarning	FailureDefinitionId	The solution is failing to do segments which are parallel and should intersect.
P FamilySymbolNestingElementsError	FailureDefinitionId	The fitting family contains unsupported nested elements or sub-elements. Please update the routing preference by selecting a different fitting type.
P FittingParamsCauseGeometryToFailError	FailureDefinitionId	The one of parameters for the fitting is causing the geometry to fail.
P FittingParamsCauseGeometryToFailWarning	FailureDefinitionId	The one of parameters for the fitting is causing the geometry to fail.
P HighlightedElementDisconnected	FailureDefinitionId	The highlighted element has been disconnected.
P InappropriateSlopeForPipe	FailureDefinitionId	The slope that you specified could not be applied to this pipe. Please check the items that it is connected to and make sure that they aren't constraining the slope of them.
P MismatchedSystemClassificationHasSystemWarning	FailureDefinitionId	The selected fixture is part of a system with different classification. System calculations (e.g. flow analysis) are not possible between systems with different classifications.
P MismatchedSystemClassificationNoSystemWarning	FailureDefinitionId	The selected fixture is assigned to a system with different classification.
P MismatchedSystemTypeWarning	FailureDefinitionId	The selected fixture is part of a different system. You may want to edit the system type and merge two systems.
P NoAutoRouteSolutionFoundError	FailureDefinitionId	No auto-route solution was found.
P NoAutoRouteSolutionFoundWarning	FailureDefinitionId	No auto-route solution was found.
P NoFittingInProjectError	FailureDefinitionId	The routing solution failed because there is no default fitting type specified or the fitting cannot be found in the project. Ensure the fitting is loaded in the project and try again.
P NoFittingInProjectWarning	FailureDefinitionId	The routing solution failed because there is no default fitting type specified or the fitting cannot be found in the project. Ensure the fitting is loaded in the project and try again.
P NoFittingInRoutingError	FailureDefinitionId	The fitting that is converted to was not defined. Please assign one in the routing preference.
P NoFittingLoadedInProjectError	FailureDefinitionId	The fitting that is converted to was not defined. Please load one fitting family and assign it in the routing preference.
P NoSolutionInView	FailureDefinitionId	There is no solution for this view. All the elements have been filtered for this view, select another view, and select solutions.
P NotAllPartsWereConvertedCannotAddPlaceholderWarning	FailureDefinitionId	Not all parts were converted. Placeholders could not be added to fill the gap (the gap was too small). Check the fabrication service definition for the system.
P NotAllPartsWereConvertedPlaceholdersWereAddedWarning	FailureDefinitionId	Not all parts were converted. Placeholders were added to fill the gaps. Check the fabrication service definition for the system.
P NotEnoughRoomForFittingsError	FailureDefinitionId	There was not enough room to place the required fittings. Consider increasing the length of the segments, or moving them farther apart to generate a solution.
P NotEnoughRoomForFittingsWarning	FailureDefinitionId	There was not enough room to place the required fittings. Consider increasing the length of the segments, or moving them farther apart to generate a solution.
P NoValidSolutionAtSelectedPoint	FailureDefinitionId	No valid auto-route solution at selected point.
P OverrideFabricationPartFailed	FailureDefinitionId	The fabrication part cannot be overridden. The button code you specified does not match the fabrication service. Please specify a different button code or check the fabrication service and try again.
P SegmentDrawnFromWrongSideError	FailureDefinitionId	The segment is being drawn from the wrong side to connect to the location you indicated.
P SegmentDrawnFromWrongSideWarning	FailureDefinitionId	The segment is being drawn from the wrong side to connect to the location you indicated.
P SegmentsAngleTooGreatError	FailureDefinitionId	The resulting angle between the segments is too great.
P SegmentsAngleTooGreatWarning	FailureDefinitionId	The resulting angle between the segments is too great.
P SolutionIsOppositeToConnectionError	FailureDefinitionId	The solution is in the opposite direction of the connection direction.
P SolutionIsOppositeToConnectionWarning	FailureDefinitionId	The solution is in the opposite direction of the connection direction.
P SpecifiedAnglesNotCompatibleWithLayoutError	FailureDefinitionId	The specified angles are not compatible with current layout.
P SpecifiedAnglesNotCompatibleWithLayoutWarning	FailureDefinitionId	The specified angles are not compatible with current layout.
P UnableToMakeConnectionInDirection	FailureDefinitionId	The application is unable to make a connection in that direction. If the connectors are pointing up, make sure that the elevations of the segments (ducts and pipes) are above them. If the connectors are pointing down, make sure that the elevations of the segments (ducts and pipes) are below them.
P UtilizationCoefficientOutOfRange	FailureDefinitionId	The value for Coefficient of Utilization must be between 0 and 1.
P ZeroLengthSegmentError	FailureDefinitionId	The solution is failing to do segments which are zero length.
P ZeroLengthSegmentWarning	FailureDefinitionId	The solution is failing to do segments which are zero length.