SiteFailures Properties

Name	Return Type	Description
P BuildingPadNotConnected	FailureDefinitionId	Can't create a single Pad with several connected regions.
P BuildingPadOverlap	FailureDefinitionId	Pads can't overlap (but can share edges).
P CannotComputeProperArea	FailureDefinitionId	Property Lines must close. Area will not be computed.
P CannotIntersectSiteRegions	FailureDefinitionId	Subregions cannot intersect.
P CannotMakeSurface	FailureDefinitionId	Can't construct surface.
P ContourLabelEmpty	FailureDefinitionId	Contour Label doesn't intersect any contours.
P EnterValueOrFormula	FailureDefinitionId	Enter a value or a formula starting with '='.
P GradeRegionElementsIngoreBottom	FailureDefinitionId	The current grading element has different elevations on bottom faces with existing element, however the cut/fill volume calculation will ignore the bottom faces differences.
P GradingInSamePhase	FailureDefinitionId	The Surface being Graded was created in the current Phase. Grading it will result in it being created and destroyed in the same Phase.
P NoHostForSubregion	FailureDefinitionId	This Subregion now does not appear to overlap any Toposurface with an appropriate Phase and Design Option.
P NoHostForSubregionWarn	FailureDefinitionId	This Subregion now does not appear to overlap any Toposurface with an appropriate Phase and Design Option.
P NotEnoughPointsInSurface	FailureDefinitionId	The surface must have at least three distinct Points.
P PointNotInSurface	FailureDefinitionId	A Point is outside of the Surface boundary. Insert the Point on the boundary instead, and then drag it to the desired location.
P PointRelativeOutside	FailureDefinitionId	In order to place Points relative to the existing Surface, the Point must be placed within the area of the existing Surface. The height of the new Point will be relative to the current Surface elevation at that Point.
P PropertyIntersect	FailureDefinitionId	Property lines intersect. Area calculations will not be precise.
P RegionPhaseMismatch	FailureDefinitionId	Subregions must have the same Phase Created parameter and Phase Demolished parameter as the host Toposurface. Subregion phase will be set to match the Toposurface.
P ResetToposurfacePhaseCreated	FailureDefinitionId	The parameter Phase Created of the Toposurface is not set to the first Phase. No pre-existing toposurface were detected. The parameter will be reset to the first Phase unless Keep Phase Created option is picked.
P SiteEditPointsClipped	FailureDefinitionId	Portions of the topographic surface or points on the surface may not be visible in this view due to clipping by the view.
P SiteEditPointsInvisible	FailureDefinitionId	Topographic elements are not visible in your current view. You can modify View Range settings in the view's Properties or Visibility settings in Visibility/Graphics. It is often easier to edit topography in a Site view or a 3D view.
P SiteMergeDisconnected	FailureDefinitionId	The two surfaces you are trying to merge are disconnected from one another. They should overlap, or at least share edges.
P SitePhasesDontOverlap	FailureDefinitionId	The phases of the two surfaces you are merging do not overlap. You can continue the operation, or cancel it and select a different pair of surfaces.
P SiteRegionOptionConflict	FailureDefinitionId	Subregions must be in the same Design Option as their Toposurface.
P SurfaceSelfIntersection	FailureDefinitionId	The splitting boundary drawn would result in a self-intersection of the surface boundary. Please edit your splitting lines to correct the problem.
P SurfaceSplit	FailureDefinitionId	The splitting boundary must split the Surface into exactly two pieces.
P SurfaceSplitError	FailureDefinitionId	The splitting boundary must split the Surface into exactly two pieces.
P SurfaceSplitNoIntersection	FailureDefinitionId	The splitting boundary must divide the Surface into separate pieces. There may be a gap in the splitting Lines or the Sketch may be incomplete.
P SurfaceTriangulationFailed	FailureDefinitionId	The Site Surface failed to triangulate.
P ToposolidSlopeExceedsThreshold	FailureDefinitionId	Thickness of this Toposolid may be slightly inaccurate due to extreme Shape Editing. Dimensions to this element in sections and details may not accurately indicate the Thickness shown in Type Properties.