CanBeHookNormal
Version comparisonPer-version detail
Click a version below to see what changed in that release vs your current frame (2026).
Not present in: 2027
2026
current
RebarFreeFormAccessor.CanBeHookNormal(Int32, Int32, XYZ)
Became obsolete in 2026: This method is deprecated in Revit 2026 and may be removed in a later version of Revit. Please use RebarFreeFormAccessor.CanBeTerminationPlaneNormal instead.
| barIndex | Int32 | The index of bar for which it will try to see if termination's plane normal is applicable. |
| end | Int32 | The end of bar. Should be 0 for start, 1 for end. |
| normal | XYZ | The teriantion's (e.g. hook, crank) plane normal that will be tested. |
| → returns | Boolean | A vector can be termination's (e.g. hook, crank) normal if for a bar specified by index, the bar direction is not parallel with the vector. |
RebarFreeFormAccessor.CanBeHookNormal(Int32, Int32, XYZ)
Became obsolete in 2026: This method is deprecated in Revit 2026 and may be removed in a later version of Revit. Please use RebarFreeFormAccessor.CanBeTerminationPlaneNormal instead.
| barIndex | Int32 | The index of bar for which it will try to see if termination's plane normal is applicable. |
| end | Int32 | The end of bar. Should be 0 for start, 1 for end. |
| normal | XYZ | The teriantion's (e.g. hook, crank) plane normal that will be tested. |
| → returns | Boolean | A vector can be termination's (e.g. hook, crank) normal if for a bar specified by index, the bar direction is not parallel with the vector. |
RebarFreeFormAccessor.CanBeHookNormal(Int32, Int32, XYZ)
Became obsolete in 2026: This method is deprecated in Revit 2026 and may be removed in a later version of Revit. Please use RebarFreeFormAccessor.CanBeTerminationPlaneNormal instead.
| barIndex | Int32 | The index of bar for which it will try to see if termination's plane normal is applicable. |
| end | Int32 | The end of bar. Should be 0 for start, 1 for end. |
| normal | XYZ | The teriantion's (e.g. hook, crank) plane normal that will be tested. |
| → returns | Boolean | A vector can be termination's (e.g. hook, crank) normal if for a bar specified by index, the bar direction is not parallel with the vector. |
RebarFreeFormAccessor.CanBeHookNormal(Int32, Int32, XYZ)
Became obsolete in 2026: This method is deprecated in Revit 2026 and may be removed in a later version of Revit. Please use RebarFreeFormAccessor.CanBeTerminationPlaneNormal instead.
| barIndex | Int32 | The index of bar for which it will try to see if termination's plane normal is applicable. |
| end | Int32 | The end of bar. Should be 0 for start, 1 for end. |
| normal | XYZ | The teriantion's (e.g. hook, crank) plane normal that will be tested. |
| → returns | Boolean | A vector can be termination's (e.g. hook, crank) normal if for a bar specified by index, the bar direction is not parallel with the vector. |
RebarFreeFormAccessor.CanBeHookNormal(Int32, Int32, XYZ)
Became obsolete in 2026: This method is deprecated in Revit 2026 and may be removed in a later version of Revit. Please use RebarFreeFormAccessor.CanBeTerminationPlaneNormal instead.
| barIndex | Int32 | The index of bar for which it will try to see if termination's plane normal is applicable. |
| end | Int32 | The end of bar. Should be 0 for start, 1 for end. |
| normal | XYZ | The teriantion's (e.g. hook, crank) plane normal that will be tested. |
| → returns | Boolean | A vector can be termination's (e.g. hook, crank) normal if for a bar specified by index, the bar direction is not parallel with the vector. |
RebarFreeFormAccessor.CanBeHookNormal(Int32, Int32, XYZ)
Became obsolete in 2026: This method is deprecated in Revit 2026 and may be removed in a later version of Revit. Please use RebarFreeFormAccessor.CanBeTerminationPlaneNormal instead.
| barIndex | Int32 | The index of bar for which it will try to see if termination's plane normal is applicable. |
| end | Int32 | The end of bar. Should be 0 for start, 1 for end. |
| normal | XYZ | The teriantion's (e.g. hook, crank) plane normal that will be tested. |
| → returns | Boolean | A vector can be termination's (e.g. hook, crank) normal if for a bar specified by index, the bar direction is not parallel with the vector. |
RebarFreeFormAccessor.CanBeHookNormal(Int32, Int32, XYZ)
Became obsolete in 2026: This method is deprecated in Revit 2026 and may be removed in a later version of Revit. Please use RebarFreeFormAccessor.CanBeTerminationPlaneNormal instead.
| barIndex | Int32 | The index of bar for which it will try to see if termination's plane normal is applicable. |
| end | Int32 | The end of bar. Should be 0 for start, 1 for end. |
| normal | XYZ | The teriantion's (e.g. hook, crank) plane normal that will be tested. |
| → returns | Boolean | A vector can be termination's (e.g. hook, crank) normal if for a bar specified by index, the bar direction is not parallel with the vector. |