MEPFabricationFailures

Description:
Failures about MEP fabrication.

Inheritance Hierarchy:
System.Object
Autodesk.Revit.DB.BuiltInFailures.MEPFabricationFailures

public static class MEPFabricationFailures

Public NotInheritable Class MEPFabricationFailures

public ref class MEPFabricationFailures abstract sealed

[<AbstractClassAttribute>]
[<SealedAttribute>]
type MEPFabricationFailures = class end

Name	Return Type	Description
P AdditionalPartNotLoaded	FailureDefinitionId	An additional part was not loaded.
P CannotConvertFlexPipeToPart	FailureDefinitionId	Cannot convert flex pipe to fabrication part.
P CannotMatchFabricationHangerSizeToHost	FailureDefinitionId	The hanger cannot be re-sized to match the re-sized host.
P FabDbChangeConn	FailureDefinitionId	Fabrication Database changes altered connectivity
P FabDbOpenJobConn	FailureDefinitionId	Fabrication job imported had bad connectivity
P FabDbSwapOut	FailureDefinitionId	Fabrication Database reload could not swap out for newer parts.
P FabricationConfigurationCorrupted	FailureDefinitionId	It looks that the Fabrication Configuration %1!s! was corrupted, please check it at %2!s!.
P FabricationHangerCannotBeSloped	FailureDefinitionId	A hanger cannot be sloped or placed on a sloped element.
P FabricationHangerHostNotFound	FailureDefinitionId	The hanger will disconnect because we can't find the suitable host.
P FabricationHangerNotConnectToHost	FailureDefinitionId	Fabrication Hanger didn't connect to the %s host.
P FabricationHangerOutOfHost	FailureDefinitionId	The hanger is out of its host and will be disconnected.
P FabricationHangerSizeNotMatch	FailureDefinitionId	The hanger size does not match the size of the host, so it can not be connected.
P FabricationOutOfSizeCondition	FailureDefinitionId	The fabrication part size is not within the correct size range for the service button condition.
P FabricationOverSizedCheck	FailureDefinitionId	Fabrication part is too large to fit on the sheet metal. Replace the part with multiple smaller parts, or notify the CAM operator.
P FabricationPartBadConnectionAlignmentWarning	FailureDefinitionId	The connection invalid due to the connector are not aligned and/or this is a gap between the connectors.
P FabricationPartBadConnectionConnectivityWarning	FailureDefinitionId	The connection invalid due to connection types associated to the connectors are not compatible.
P FabricationPartBadConnectionSizeWarning	FailureDefinitionId	The connection invalid due to connectors sizes are not the same.
P FabricationPartCannotBeMirrored	FailureDefinitionId
P FabricationPartCannotChangeServiceSizeWarning	FailureDefinitionId	The selected fitting(s) cannot successfully change service or change size. You must disconnect the connections on the fitting(s) and try again.
P FabricationPartCannotChangeSlopeError	FailureDefinitionId	The connected fitting(s) cannot successfully change to the new slope value. You may try to disconnect the connections on the fitting(s) and try again.
P FabricationPartCannotChangeTypeBadDimError	FailureDefinitionId	The selected fitting(s) cannot successfully change the type. The newly selected fabrication part may have badly configured dimensions or be constrained due to connected fitting(s). You may try to disconnect the connections on the fitting(s) and try again.
P FabricationPartCannotChangeTypeBadDimUnConnError	FailureDefinitionId	The selected fitting(s) cannot successfully change the type. The newly selected fabrication part may have badly configured dimensions, resulting in bad geometry.
P FabricationPartCannotChangeTypeError	FailureDefinitionId	The selected fitting(s) cannot successfully change the type. You must disconnect the connections on the fitting(s) and try again.
P FabricationPartCannotChangeTypeIncompatError	FailureDefinitionId	The selected fitting(s) cannot successfully change the type. The newly selected fabrication part type either has no material or has badly configured dimensions, resulting in bad geometry. You may try to disconnect the connections on the fitting(s) and try again.
P FabricationPartCannotChangeTypeIncompatUnConnError	FailureDefinitionId	The selected fitting(s) cannot successfully change the type. The newly selected fabrication part type either has no material or has badly configured dimensions, resulting in bad geometry.
P FabricationPartCannotChangeTypeMisalignedError	FailureDefinitionId	The selected fitting(s) cannot successfully change the type. The newly selected fabrication part type has a problem with the angle dimension of the current fitting(s), resulting in bad geometry. You may try to disconnect the connections on the fitting(s) and try again.
P FabricationPartCannotChangeTypeMisalignedUnConnError	FailureDefinitionId	The selected fitting(s) cannot successfully change the type. The newly selected fabrication part type has a problem with the angle dimension of the current fitting(s), resulting in bad geometry.
P FabricationPartCannotChangeTypeUnConnError	FailureDefinitionId	The selected fitting(s) cannot successfully change the type.
P FabricationPartCannotChangeTypeWarning	FailureDefinitionId	The selected fitting(s) cannot maintain connections to existing fabrication parts due to size, direction or angle differences. You must manually reconnect the open connections.
P FabricationPartExceededAngleFlexToleranceWarning	FailureDefinitionId	The angle flex is greater than the maximum angle flex tolerance defined by the fabrication part. Connections with this part may not be properly aligned and may appear to be skewed.
P FabricationPartExcludedPartWarning	FailureDefinitionId	There were fabrication parts needed to the make the connection that were excluded from the fabrication service causing the connection to fail. You may try to inlcude these fitting(s) and try again.
P FabricationPartFitFailure	FailureDefinitionId	Fabrication Part Fitting Failed to Fit
P FabricationPartFitFailWarning	FailureDefinitionId	Fabrication Part Fitting Failed to Fit
P FabricationPartHasInvalidGeometry	FailureDefinitionId	The fabrication part either has no material or has badly configured dimensions, resulting in bad geometry.
P FabricationPartInvalidConnection	FailureDefinitionId	Fabrication Part connection invalid and could not be automatically coupled.
P FabricationPartInvalidInsulationSpecificationWarning	FailureDefinitionId	The insulation specification is invalid for the pinned fabrication part.
P FabricationPartInvalidSpecification	FailureDefinitionId	The part specification is invalid.
P FabricationPartNoPartTypeFound	FailureDefinitionId	There are no fabrication part types found for the current Configuration and Service. Please select settings and reload the service to create the fabrication part types.
P FabricationPartNotAttachedToStraight	FailureDefinitionId	The part must be attached to straight.
P FabricationPartOptimizeInvalidConnection	FailureDefinitionId	No available couplings to connect standard lengths for this instance of straight.
P FabricationRodDetachFromHangerError	FailureDefinitionId	The rod need to be detached from hanger.
P FabricationRodsConnectionChangedWarning	FailureDefinitionId	The structural component that the hanger is attached to has changed to a different element.
P FabricationRodsDisconnectedError	FailureDefinitionId	The hanger rod was disconnected because there is no structural component above.
P FabricationRodsDisconnectedWarning	FailureDefinitionId	The hanger rod was disconnected because there is no structural component above.
P FabricationServiceMismatch	FailureDefinitionId	Attempting to connect fabrication parts from different services.
P FabricationStraigtLengthOversized	FailureDefinitionId	Fabrication straight exceeds the standard length. Use the Optimize Length command to adjust the length.
P FixedFabricationPartNotChangeLength	FailureDefinitionId	Failed to change length of fixed part.
P GroupedFabricationPartNotReposition	FailureDefinitionId	Failed to reposition part.
P HangerProfileNotMatchWithHost	FailureDefinitionId	The defined hanger profile does not match with the host.
P HangerWidthOutOfRange	FailureDefinitionId	The hanger width is too large to show.
P InvalidConnectionsHaveBeenDisconnected	FailureDefinitionId	Invalid connections have been disconnected. Please reconnect them manually or use different fittings.
P InvalidSelectionThereCannotBeOpenConnectors	FailureDefinitionId	Invalid selection there cannot be any open connectors for the design to fabrication part tool.
P NoStructuralHostToAttachWarning	FailureDefinitionId	There is no structural component to attach the hanger rod to.
P NotAllPartsWereConvertedUnsuportedFittingOffsets	FailureDefinitionId	Not all parts were converted. Eccentric transitions and taps that have offsets from the center line are unsupported and cannot be converted.
P PinnedFabricationPartNotChangeExtension	FailureDefinitionId	Failed to change extension of part.
P PinnedFabricationPartNotReposition	FailureDefinitionId	Failed to reposition part.
P PlaceCutinFittingFailed	FailureDefinitionId	Failed to insert part.
P SizeNotAvailableInFabricationService	FailureDefinitionId	Sizes:%1!s! in system %2!s! are not available in fabrication service:%3!s!, All available sizes are:\n%4!s!.
P UneditableFabricationPartNotReposition	FailureDefinitionId	Failed to reposition part.