StairRampFailures

Description:
Failures about StairRamp.

Inheritance Hierarchy:
System.Object
Autodesk.Revit.DB.BuiltInFailures.StairRampFailures

public static class StairRampFailures

Public NotInheritable Class StairRampFailures

public ref class StairRampFailures abstract sealed

[<AbstractClassAttribute>]
[<SealedAttribute>]
type StairRampFailures = class end

Name	Return Type	Description
P ActualRiserHeightChanged	FailureDefinitionId	The actual riser height for one or more stairs violates the maximum set in the type.
P AntiparallelRampRisers	FailureDefinitionId	Riser lines are parallel but not collinear. Can't build Run between these Risers.
P AntiparallelRampRisersError	FailureDefinitionId	Riser lines are parallel but not collinear. Can't build Run between these Risers.
P ArcRunRadiusTooSmall	FailureDefinitionId	Can't create Run. Run radius is too small.
P ArcRunWidthTooLongFailure	FailureDefinitionId	Arc run width is too long.
P AutomaticLandingConvertedToSketchedLandingWarning	FailureDefinitionId	Some run(s) are deleted, so automatic landing is converted to sketched landing.
P BadBalustersPerTread	FailureDefinitionId	Number of Balusters per Tread must be an integer greater than zero.
P BadFillingSpacing	FailureDefinitionId	Spacing for Excess Length Fill is too small.
P BadRailings	FailureDefinitionId	Can't create Railings.
P BadRailingsError	FailureDefinitionId	Can't create Railings.
P BadRailProfile	FailureDefinitionId	One or more Profile Loops are invalid, probably because of self-intersection.
P BadTreadRiserProfile	FailureDefinitionId	Tread/Riser profile is invalid.
P BalustersTooClose	FailureDefinitionId	Baluster Separation must be equal to or greater than the Baluster widths.
P BalustersTooCloseAbsolute	FailureDefinitionId	Baluster Separation is too small.
P BalusterUpsideDown	FailureDefinitionId	Top reference is below Bottom reference for one or more Balusters. These Balusters are not created.
P CannotAlignSupportOnPosts	FailureDefinitionId	Cannot align the support on the posts.
P CannotComputeRailElevation	FailureDefinitionId	Can't compute elevation profile for one or more Rails
P CannotCreateBaluster	FailureDefinitionId	Can't create Balusters for given Width and Height.
P CannotCreateBalusterPatterns	FailureDefinitionId	Can't create Baluster Patterns for Railings
P CannotCreateCornerBalusters	FailureDefinitionId	Can't create corner Baluster
P CannotCreateLandingStringer	FailureDefinitionId	Can't create stringer at landing.
P CannotCreateMiddleStringer	FailureDefinitionId	Can't create one or more Middle Stringers.
P CannotCreateMonolithicStairs	FailureDefinitionId	Can't make monolithic Stairs.
P CannotCreateNosing	FailureDefinitionId	Can't create nosing on one or more treads.
P CannotCreateOneOrMoreBaluster	FailureDefinitionId	Can't create one or more Balusters
P CannotCreateOneOrMoreTreads	FailureDefinitionId	Can't create geometry for one or more treads.
P CannotCreateOpenMiddleStringers	FailureDefinitionId	Can't cut open/middle stringers geometry.
P CannotCreateRail	FailureDefinitionId	Can't create Railing. Thickness of Rail or Balusters might be too small. If you don't want Balusters, specify "None" for Baluster Shape.
P CannotCreateRailGeom	FailureDefinitionId	Can't create geometry for one or more Rails
P CannotCreateRailWarn	FailureDefinitionId	Can't create Railing. Thickness of Rail or Balusters might be too small. If you don't want Balusters, specify "None" for Baluster Shape.
P CannotCreateRiser	FailureDefinitionId	Can't create geometry for one or more risers.
P CannotCreateSideStringer	FailureDefinitionId	Can't create one or more Side Stringers.
P CannotCreateStairForLevelOverlapping	FailureDefinitionId	Some of the multistory stairs couldn't be created due to the overlapped levels.
P CannotCreateStringers	FailureDefinitionId	Can't create stringers geometry.
P CannotDrawStairs	FailureDefinitionId	Can't make stairs
P CannotDrawStairsError	FailureDefinitionId	Can't make stairs
P CannotEndWithZeroRiser	FailureDefinitionId	Can't end Stairs with Riser because Riser Thickness is too small.
P CannotGenerateFaces	FailureDefinitionId	Couldn't generate surfaces for stairs.
P CannotGenerateFacesError	FailureDefinitionId	Couldn't generate surfaces for stairs.
P CannotGenerateRamp	FailureDefinitionId	Couldn't generate surfaces for ramp.
P CannotGenerateRampError	FailureDefinitionId	Couldn't generate surfaces for ramp.
P CannotMakeLanding	FailureDefinitionId	Can't make landing.
P CannotOffsetBoundary	FailureDefinitionId	Can't create Boundary as an offset of Run Curve
P CannotOffsetRail	FailureDefinitionId	Can't create one or more Rails with desired offset
P CannotPlaceBalusterOffset	FailureDefinitionId	Can't place Balusters and/or Rails with desired offset
P CannotPlaceBalusterPatterns	FailureDefinitionId	Can't place Baluster Patterns
P CannotPlaceRailingOnStringerWarning	FailureDefinitionId	Railing is placed on tread because there is no stringer.
P CannotProcessInStairsSketchEditMode	FailureDefinitionId	Cannot process when stair(s) in sketch edit mode.
P CannotSplitRailingWithExtensions	FailureDefinitionId	Railings with extensions cannot be split.
P ContinuousRailFilletCreationError	FailureDefinitionId	Cannot create specified fillet at rail path corner.
P ContinuousRailFilletCreationParallel	FailureDefinitionId	Cannot create specified fillet at rail path corner because of the curves are already smoothed.
P ContinuousRailFilletCreationWarning	FailureDefinitionId	Cannot create specified fillet at rail path corner.
P ContinuousRailGometryCreationFailure	FailureDefinitionId	Cannot create the continuous rail geometry.
P ContinuousRailNotContinuous	FailureDefinitionId	The rail is non-continuous.
P ContinuousRailSupportPlacementFailure	FailureDefinitionId	Cannot place the supports along the rail path.
P ContinuousRailTransitionFailure	FailureDefinitionId	Cannot create specified transition at rail path turn, hand Rail/Top Rail cannot maintain continuous.
P ExtendBelowBaseGreaterThanLandingBaseElevation	FailureDefinitionId	Extend Below Base needs to be less than Landing Base Elevation.
P ExtendBelowBaseGreaterThanRunTopElevation	FailureDefinitionId	Extend Below Base needs to be less than Run Top Elevation.
P FailToReOrientSketchCurvesFailure	FailureDefinitionId	Failed to orient sketch curves.
P HeightOfRunIsTooSmall	FailureDefinitionId	Height of run is too small.
P IntermediateLandingHigherThanTopRunFailure	FailureDefinitionId	Run is reversed.
P InvalidBalustersPattern	FailureDefinitionId	Invalid Balusters Pattern
P InvalidLocationLineJustificationFailure	FailureDefinitionId	Modify the location justification to a invalid value.
P InvalidParameters	FailureDefinitionId	Stairs run or landing has invalid parameter(s).
P InvalidRailProfile	FailureDefinitionId	Profiles for one or more of the Rails are invalid. Make sure that every used Profile is a closed series of non-intersecting Lines.
P InvalidStairsPathFailure	FailureDefinitionId	Invalid stairs path provided.
P InvalidStartLevel	FailureDefinitionId	The start level and end level for this staircase must be at different elevations.
P InvalidStartLevelRamp	FailureDefinitionId	The start level and end level for this ramp must be at different elevations.
P LandingDepthIsLessThanRunWidthWarning	FailureDefinitionId	Landing depth is less than run width.
P LandingHeightUnderStairsBottom	FailureDefinitionId	Cannot make landing because height of landing is equal or less than to bottom height of the stair.
P LandingShapeHandleOnPinnedRunFailure	FailureDefinitionId	Cannot Drag the automatic landing shape handle control because the connected run is pinned.
P MayUnjoinRailAndSupports	FailureDefinitionId	Fillet may cause the supports unjoin with the rail.
P MultistoryLevelBelowTopbottomLevel	FailureDefinitionId	Multistory top level must be above the stair/ramp top and bottom levels.
P MultistoryLevelBelowTopbottomLevelError	FailureDefinitionId	Multistory top level must be above the stair/ramp top and bottom levels.
P MultistoryStairDoesntReach	FailureDefinitionId	The multistory stair/ramp could not reach its top level with integral number of flights. Maximum number of flights below the top level is created.
P MultistoryStairsAutomaticLevelLandingsDeleted	FailureDefinitionId	Level landings are deleted because the connected stairs have been regenerated.
P MultistoryStairsComponentJoinFailure	FailureDefinitionId	Can't keep elements joined. Avoid converting stairs to skeched-based component in Multistory stairs.
P MultistoryStairsHideTopLevelParameter	FailureDefinitionId	You have set the stair's multistory top level to None, and Revit will remove this parameter, if you want to create a multistory stair, please use Create Multistory Stair feature.
P MultistoryStandardStairBottomEndExceedsOrNotReach	FailureDefinitionId	One of the stairs inside multistory stairs bottom ends exceeds or cannot reach the base elevation of the stair.
P MultistoryStandardStairTopEndExceedsOrNotReach	FailureDefinitionId	One of the stairs inside multistory stairs top ends exceed or cannot reach the top elevation of the stair.
P MultusegmentRampRiser	FailureDefinitionId	Ramp can't have multisegment Riser.
P MultusegmentRampRiserError	FailureDefinitionId	Ramp can't have multisegment Riser.
P NoCurvesInRailing	FailureDefinitionId	Railing Sketch has no Lines.
P NoProfileForRail	FailureDefinitionId	Must specify Profiles for every Rail.
P NoRailingsStringer	FailureDefinitionId	Railings and Stringers will not be automatically generated due to bad Runs. This message may be incorrect if you have Edited the Sketch and modified some dimensions.
P NoRisersInPureMonolithicStairs	FailureDefinitionId	Monolithic Stairs with zero tread thickness can't have risers
P NoRunsRamp	FailureDefinitionId	Ramp has no Runs. Can't create Ramp.
P NoRunsRampError	FailureDefinitionId	Ramp has no Runs. Can't create Ramp.
P NotALineRiserRamp	FailureDefinitionId	Riser line must be a straight line for Ramps.
P NotALineRiserRampError	FailureDefinitionId	Riser line must be a straight line for Ramps.
P NotchThicknessIsLargerThanLandingWarning	FailureDefinitionId	The notch thickness is larger than landing.
P NotEnoughRisers	FailureDefinitionId	Actual Number of Risers is different from Desired Number of Risers. Add/remove Risers or change Desired Number of Risers in Stairs Properties.
P OnlyMonolithicStairs	FailureDefinitionId	Tread thickness can't be zero for non-monolithic stairs
P PartOfRiserLiesOnBoundaryFailure	FailureDefinitionId	Part of the riser lies on the boundary is not allowed.
P PathDoesntJoinToBorderRisersFailure	FailureDefinitionId	Path doesn't join to border risers is not allowed.
P RailCurveTooShort	FailureDefinitionId	Curve in rail sketch is too short for rail creation and ignored.
P RailingBadOffset	FailureDefinitionId	An arc in the railing sketch has a radius that conflicts with the current rail widths and offsets. Please either increase the radius or modify rail profiles and offsets.
P RailingCurvesNotSplitRamp	FailureDefinitionId	The slope of this railing will not parallel the ramp at landings. To get a parallel railing, split the railing sketch at the ends of landings.
P RailingCurvesNotSplitStairs	FailureDefinitionId	The slope of this railing may not parallel the stairs at runs and landings. To get a parallel railing, split the railing sketch at the ends of landings.
P RailingDoublyConnected	FailureDefinitionId	Railings hosted on Stairs must form a single, open, connected line.
P RailingNotConnected	FailureDefinitionId	The Railing line must be a single connected Sketch. If you want separate pieces of Railing, create two or more separate Railings.
P RailPathCloseLoopForExtensionWarning	FailureDefinitionId	The rail path is closed at the start and end path point for extension creation.
P RailPlacedOutsideOfHost	FailureDefinitionId	Railings are placed completely outside the host. It may change the adjustment of the railing to the host and its vertical position.
P RailProfileLowerThanFilletError	FailureDefinitionId	Fillet cannot be created between rail segment since the radius is lower than the profile size.
P RailProfileLowerThanFilletFailure	FailureDefinitionId	Fillet cannot be created between rail segment since the radius is lower than the profile size.
P RailProfileOpen	FailureDefinitionId	Open Profile Loop can't be used as a Rail Profile
P RailTypeChangeInconsistancyWarningWithResetBtn	FailureDefinitionId	Some rail type changes are not consistent with your rail instances customization in this project, you can reset them to make them corresponding with your changes.
P RampDoesntReach	FailureDefinitionId	The ramp is not long enough to reach the top constraint. Change the slope or increase the length of the ramp.
P RampDoesntReachOffset	FailureDefinitionId	The ramp is not long enough to reach the top constraint plus top offset. Change the slope or increase the length of the ramp.
P RampLandingNotCreated	FailureDefinitionId	Beginning of run coincide with the end of previous run. Landing is not created between runs.
P RampRunTooComplex	FailureDefinitionId	Ramp Run has complex boundary and may produce unreasonable geometry. Split it into few Runs by inserting Riser Lines at the end of each Run and at the beginning of the next one. If you want to create Ramp with arc an straight section you can do it using a Run tool.
P RampStartHigherThanEnd	FailureDefinitionId	The ramp's base (base level + base offset) must be below its top (top level + top offset).
P RiserCurveTooShort	FailureDefinitionId	Riser curve is too short to create nosing on it.
P RiserHeightIsTooSmall	FailureDefinitionId	Riser height is too small.
P RiserIntWithBoundaryMoreThanOnceFailure	FailureDefinitionId	Riser intersects with boundary more than once.
P RisersAtSameLocation	FailureDefinitionId	The highlighted risers have the same location along the boundary line. Please move one of the two risers.
P RiserThicknesssResetToZero	FailureDefinitionId	Monolithic Stairs without Treads can't have Risers. Riser Thickness for Stairs Type was automatically set to zero.
P RunBottomHigherThanTopFailure	FailureDefinitionId	The base elevation for the run is higher than the top elevation for the run.
P RunBottomUnderStairsBottomFailure	FailureDefinitionId	Run bottom elevation should not be below the stairs bottom elevation.
P RunIsJoiningLandingWithRiserSoNotchDoesNotWorkWarning	FailureDefinitionId	Run is joining landing with riser, so notch configuration does not take effect. Try to set run as begin/end with tread to make a notch.
P RunTopLowerThanBottomFailure	FailureDefinitionId	The top elevation for the run is lower than the base elevation for the run.
P SpiralRunRadiusTooSmallFailure	FailureDefinitionId	The radius value for the run is too small.
P StairIncompleteFailure	FailureDefinitionId	Stair element is incomplete, not all components are logic connected.
P StairsActualRiserHeightGreaterThanMaximumFailure	FailureDefinitionId	Computed actual riser height of stairs is greater than maximum riser height defined in stairs type.
P StairsActualRunWidthLessThanMinimumFailure	FailureDefinitionId	Actual run width is less than minimum run width defined in stairs type.
P StairsActualTreadDepthLessThanMinimumFailure	FailureDefinitionId	Computed actual tread depth of stairs is less than minimum tread depth defined in stairs type.
P StairsAlreadyAttachedToCurrentLevel	FailureDefinitionId	Mutistory Stairs already have a Stair attaching to this level.
P StairsAreUpdatedDueToLevelHeightChange	FailureDefinitionId	Stair component(s) in the multistory stair are updated due to the level height changes.
P StairsAutomaticLandingLayoutFailure	FailureDefinitionId	Fail to generate the automatic landing layout
P StairsAutomaticLandingLayoutWarn	FailureDefinitionId	Fail to generate the automatic landing layout
P StairsBottomEndExceedsOrNotReachWarning	FailureDefinitionId	Stair bottom end exceeds or cannot reach the base elevation of the stair. Add/remove risers at the bottom end or change base elevation settings in Stair Properties.
P StairsCannotExtendToFloorStructureLayerWarning	FailureDefinitionId	Stairs cannot extend to floor structure layer.
P StairsCommonRunGenerateLayoutFailure	FailureDefinitionId	Fail to get base line thus fail to generate run layout
P StairsComponentJoinFailure	FailureDefinitionId	Can't keep elements joined.
P StairsCrossingRisersDisallowedFailure	FailureDefinitionId	Crossing risers are not allowed
P StairsGenericFailure	FailureDefinitionId	Stairs generic failure
P StairsGenericTransformFailure	FailureDefinitionId	Cannot change base elevation of Stairs
P StairsIllegalDesiredNumRisers	FailureDefinitionId	Desired Number of Risers is too small. Computed Actual Riser Height is greater than Maximum Riser Height allowed by type.
P StairsInMultistoryExceedTopConstraint	FailureDefinitionId	Stairs in MultistoryStairs after adjusting still exceed the top constraint.
P StairsOnlySingleBoundaryHasRiserWithBothEndsOnBoundaryFailure	FailureDefinitionId	Only single boundary case may have riser with its both ends on boundary.
P StairsOtherThan2IntsByRiserAndBoundaryFailure	FailureDefinitionId	More than 2 intersection points between riser segment and boundary encountered
P StairsPathCopyReferenceLostFailure	FailureDefinitionId	Some stair paths were not copied because some references were lost.
P StairsPathPositionResetWarning	FailureDefinitionId	The stairs path doesn't intersect with riser lines.
P StairsRunRunJoinNotAllowedFailure	FailureDefinitionId	Run-Run join is not allowed of they have same "Start With Riser"/"End With Riser" configuration at the joined end.
P StairsStartHigherThanEnd	FailureDefinitionId	The stairs' base (Base Level + Base Offset) must be below its top (Top Level + Top Offset).
P StairsStringerCannotBeCreated	FailureDefinitionId	The stairs stringer cannot be created.
P StairsSubElementsNotConnectedWarning	FailureDefinitionId	Stair sub-elements are not connected
P StairsSupportOverlapFailure	FailureDefinitionId	Some supports overlap with others
P StairsSupportTooShort	FailureDefinitionId	A short support is being created.
P StairsTopEndExceedsOrNotReachWarning	FailureDefinitionId	Stair top end exceeds or cannot reach the top elevation of the stair. Add/remove risers at the top end or change top elevation settings in Stair Properties.
P StairsTopLowerThanBaseFailure	FailureDefinitionId	The top of the Stair is lower than the base of the Stair
P StairStringerCantOffset	FailureDefinitionId	Inside stringer could not be created because of insufficient space. Please disable the inside stringer or decrease its width.
P StairsWinderGenLayoutFailure	FailureDefinitionId	Fail to generate run layout and then cannot make winder run
P StairsWinderInvalidParamsFailure	FailureDefinitionId	Cannot create the winder run because some values for the instance properties cannot be satisfied.
P StairsZeroDesiredRisers	FailureDefinitionId	The number of desired risers for a staircase cannot be 0.
P StringerCurvesNotSplitStairs	FailureDefinitionId	The slope of stringer may not parallel runs and landings. To get a parallel stringer, split boundary lines at the ends of landings.
P StringerCurveTooShort	FailureDefinitionId	A piece of boundary is too short to create stringer on it.
P TooShortCurveDowngradeGeometry	FailureDefinitionId	Curve is too short and may downgrade the geometry.
P TreadDepthBelowMin	FailureDefinitionId	The Actual Tread Depth for one or more Stairs violates the Minimum Depth set in the type.
P TreadDepthFailsEq	FailureDefinitionId	The actual tread depth and riser height for one or more stairs of this type violates the stair equation.
P TreadDepthTooBigFailure	FailureDefinitionId	The tread depth is too large for the spiral run.
P TreadFrontProfileInvalid	FailureDefinitionId	This profile cannot be used for the front of treads. Please choose a profile composed of a closed loop of lines with exactly one lines coincident with the y-axis. This lines will define the connection of this profile to the tread.
P UnableToCreateMultistoryStairs	FailureDefinitionId	Unable to create Multistory stairs.
P UnexpectedCurveIntersectionFailure	FailureDefinitionId	Computing curve intersection and find the invalid result.
P WinderFilletRadiusTooLargeFailure	FailureDefinitionId	The value for Fillet Radius is too large to satisfy the Minimum Inside Width value.
P WinderFirstLegTooShortOrRunWidthTooGreatFailure	FailureDefinitionId	The first leg of winder run is too short or the runwidth is too great.
P WinderGenericError	FailureDefinitionId	Cannot make winder.
P WinderLegIsTooShortFailure	FailureDefinitionId	A winder leg is too short.
P WinderLegsAngleTooGreatOrRunWidthTooSmallFailure	FailureDefinitionId	The angle between two consecutive legs are too great or the runwidth is too small.
P WinderLegTooShortOrRunWidthTooGreatFailure	FailureDefinitionId	One leg of the winder run is too small or the runwidth is too great.
P WinderMinWidthTooLargeFailure	FailureDefinitionId	The value for Minimum Width on Inside Boundary is too large.
P WinderMinWidthTooLargeForParallelTreadsFailure	FailureDefinitionId	The value for Minimum Width on Inside Boundary is too large to satisfy the number of Parallel Treads at the Start or End as specified in the Run Instance properties.
P WinderParallelLegsFailure	FailureDefinitionId	Two consecutive legs are parallel.
P WinderParallelTreadsNumberFailure	FailureDefinitionId	Cannot satisfy the number of Parallel Treads at the Start or End as specified in the Run Instance properties
P WinderRunCreationFailure	FailureDefinitionId	The relationship between the current values of Actual Run Width, Minimum Width at Inside Boundary, and Parallel Treads at Start or End does not support the creation of the winder run.
P WinderRunInsideMinTreadDepthFailure	FailureDefinitionId	Please enter a positive value less than Actual Tread Depth on Stair Path (%Actual Tread Depth%).
P WinderRunInsideWalklineOffsetFailure	FailureDefinitionId	Please enter a value between 0 and half of Actual Run Width (%1/2 Actual Run Width%).
P WinderRunWidthLessThan2TimesMinWidthFailure	FailureDefinitionId	The value for Minimum Width on Inside Boundary is too large to satisfy the number of Parallel Treads at the Start or End as specified in the Run Instance properties.
P WinderRunWidthLessThanWalkLineOffsetFailure	FailureDefinitionId	The value for Run Width is less than two times of value of the inside walkline offset.
P WinderRunWidthOrMinWidthOrTooGreatParallelTreadsFailure	FailureDefinitionId	The parameter runwidth is great or the parameter min width at inside boundary is too great, or number of parallel treads at both ends is too great.
P WinderRunWidthOrMinWidthOrTooShortFailure	FailureDefinitionId	The parameter runwidth is too great or the parameter min width at inside boundary is too great, or one leg of winder run is too short.
P WinderSecondLegTooShortOrRunwidthTooGreatFailure	FailureDefinitionId	The second leg of winder run is too short or the runwidth is too great.
P WinderStraightStepsNumberFailure	FailureDefinitionId	The current layout cannot allow the specified number of treads. Increase the length of the run leg in the model or reduce the value for Parallel Treads at Start or Parallel Treads at End.
P WinderThirdLegTooShortOrRunWidthTooGreatFailure	FailureDefinitionId	The third leg of winder run is too short or the runwidth is too great.
P WinderTooManyEndParallelTreadsOrRunWidthFailure	FailureDefinitionId	The number of parallel treads at end is too great or the run width is too great.
P WinderTooManyParallelTreadsAtEndFailure	FailureDefinitionId	The number of parallel treads at end is too great.
P WinderTooManyParallelTreadsAtHeadFailure	FailureDefinitionId	The number of parallel treads at start is too great.
P WinderTooManyStartParallelTreadsOrRunWidthFailure	FailureDefinitionId	The number of parallel treads at start is too great or the run width is too great.